How to Replace a Bath Tub

Just how do you really feel in relation to How to Install a Bathtub Yourself?

Mounting a bath tub isn't specifically rocket science, however it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is also a moderately tough job. If the old bathtub is conveniently obtainable, the job can relocate immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a house handyman's abilities, although you will certainly require a helper to move out the old tub and set in the new one. Make sure you have actually certified yourself for the task as well as fit trying it. Instead of working with a service provider to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will help you install a brand-new bath tub in your bathroom if you have currently gotten a brand-new bathtub as well as do not require to alter the plan of your previous supply of water pipes.
Your tools and material checklist should comprise the following:

New Bath tub

Hammer

Pipeline Wrenches

Prybar

Shatterproof glass

Level

Pliers

Adjustable Wrench

Putty Knife

Screwdriver

Cold Chisel

Measuring tape

Pipeline Caps

Planning for the Setup

Firstly, the supporting structure provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to avoid stress on the bathtub.
Fit the versatile tap adapters to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must currently be ready to be suited its final placement.

Removing Old Taps

If you require to replace old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any water continuing to be in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited access that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the staying water that will originate from the pipelines. Once the supply pipes have been eliminated, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Prior to moving on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.

Installing the Bath tub

Using both wooden boards under its feet, place the bath tub in the needed setting. The wood boards are practical in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to make sure that the tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bath tub up until the spirit level reviews level.
To install taps, fit all-time low of the outermost flexible tap adapter to the ideal supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Activate the supply of water as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub as well as also examine the overflow outlet and the typical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the supplier's instruction manual. Tiling and also securing around the bath tub should wait till the bath tub has actually been utilized a minimum of once as this will certainly resolve it right into its final placement.

Suitable New Taps

If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin making certain that the washing machines are in place in between the tap and the sink. Safeguard the tap in place with the supplier supplied backnut. When the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

Tiling Around the Bathtub

In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to crack an inflexible seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, leading to difficulties with moisture and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components and also installations. They are sold in tubes and also cartridges, and also can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealer can split fairly early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant sticky and also grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you like reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Create a comment below. We'd be delighted to find out your reactions about this write up. We are looking forward to see you back again soon. If you please take the time to distribute this blog posting if you liked it. Many thanks for taking the time to read it.

Blog